No products
Top sellers
-
PUMP IMPELLER /" IMPELLOR / IMPELER /ROTOR / RUBBER BLADES"
Highest Quality -Impellor / Impeller for the water pump on a Vire 7 or...
£ 24.00 -
-
Vire 7 & Vire 12 Manual 1992 + Parts List
Operators Manual Installation manual Published by a boatyard (now...
£ 0.00 -
ignition points , contact set
contact set ignition points youtube videos how to fit and set and...
£ 23.00 -
-
VIRE 7 Core Plug set (3) Stainless Steel (Freeze plug)
Specially made for Vire motors only. Pressed from stainless steel by...
£ 14.00 -
-
VIRE 7 & 12 DRIVE-KEY (woodruff key) for impeller- s/s
Highest Quality -drive key, or woodruff key this is pressed into the...
£ 4.00 -
-
VIRE 7 DYNASTART BELT (FAN BELT )
Correct Vire sized length, tooth size and V-angle, Vire 7 standard...
£ 10.00
Categories
Suppliers
- Fashion Supplier
Top sellers
-
VIRE 6/7 Engine Mounting Vibration Dampers...
pack of 4 x Vire 6/ 7 Engine mounting (Steel Oval Base) each includes ; Steel/rubber threaded base (70mm PCD) steel BZP stud (50 x M10) 2 x washers 1 x heaight adjusting nut 1 x lock nut
£ 90.00In Stock -
Starting Solenoid / Relay
starting solenoid Bosch marinised plastic case and protected non-rusting contacts uprated to 250A instantaneous/125A continuous (double the original Vire standard) ( for all types of dynastarts )
£ 55.00In Stock -
Pull Cord (starting rope) - for all models
Pull cord (starting rope) every boat should have one, in case of flat battery or electrical problems. correct length and diameter with secure melted knotted end https://www.youtube.com/watch?v=bVLcWCKSwtw
£ 7.00Out of stock -
VIRE 7/12 Crank SEAL (3)
Set of 3x crankcase SEALS for the Vire 7/12 engine High Quality, type tested by VIRE UK over 15 years, no failures
£ 35.00In Stock -
Small End Bearing
Small End bearing - (caged steel needle) this fits in the small (top/piston) end of the connecting rod on a vire 7 or 12 engine number >22000
£ 14.00In Stock -
VIRE 7/12 Engine Mounting Vibration...
REFURBISHED (NOT NEW) might have superficial corrosion or pitting and wear but cleaned, inspected, sprayed 'good working order' Vire 7/12 Engine mounting (Alloy Rectangular Base) distance between fixing holes (PCD) 110 mm includes ; Alloy/rubber threaded base vertical steel stud metric fine pitch(not removable) 2 x washers 1 x height adjusting nut 1 x...
£ 20.00Out of stock -
CHARGE REGULATOR (solid-state charging...
CHARGING REGULATOR ( for BOSCH/SIBA type dynastarts ) with connectors kit, wiring diagram. 12 months warranty. Loyalty discount on related equipment and free Technical support for life. twice as efficient as previous electro-mechanical versions no moving or exposed parts, marine approved 30A rated (reliable unlike lower rated units)
£ 99.00In Stock -
VIRE 6 Core Plug set (3) BZP Finish
Specially made for Vire motors only. Pressed from sheet steel by precision engineers Elctro-plated with Zinc Exceeds Original specification Full set https://www.youtube.com/watch?v=gbUWPmfioqc
£ 11.00In Stock -
VIRE 6/7/12 Pump Bearing Double Race...
New pump bearing bearings for Gearbox for the Vire 6/7/12 . This bearing is highest quality Vire Marine Spec. The pictured pump shaft shown is for context and is not included
£ 35.00In Stock -
PBO 1967 Vire 6 Servicing, (Amal WICO)
Practical Boat Owner magazine article 1967, published with permission Introduces the engine, and explains how to service it covers BVR model, but the engine is same as BV and BVK based on a rare early model with WICO ignition / AMAL carburettor (later production was updated to bosch/tillotson)
£ 0.00In Stock -
PUMP SEALS & CLIPS KIT
kit for replacing and upgrading your pump shaft seals; 3 x double lipped seals (3 are better than 2 and will fit) 2 x s/s retaining clip (old steel ones rust and not normally re-usable)
£ 25.00In Stock -
CYLINDER BASE GASKET 6 hp
waterproof paper gasket, special thickness, between cylinder and crankcase check crankcase joint is level, use sealant like hylomar I have a video on youtube about this procedure
£ 6.00In Stock
