No products
Top sellers
-
PUMP IMPELLER /" IMPELLOR / IMPELER /ROTOR / RUBBER BLADES"
Highest Quality -Impellor / Impeller for the water pump on a Vire 7 or...
£ 24.00 -
-
Vire 7 & Vire 12 Manual 1992 + Parts List
Operators Manual Installation manual Published by a boatyard (now...
£ 0.00 -
VIRE 7 & 12 DRIVE-KEY (woodruff key) for impeller- s/s
Highest Quality -drive key, or woodruff key this is pressed into the...
£ 4.00 -
ignition points , contact set
contact set ignition points youtube videos how to fit and set and...
£ 23.00 -
-
-
Kit for Overhaul/Service of Tillotson Carburettor of VIRE 6/7
Vire 6 & 7 Diapragm Carb Kit (Typically 286/260 models) The...
£ 36.00 -
VIRE 7 Core Plug set (3) Stainless Steel (Freeze plug)
Specially made for Vire motors only. Pressed from stainless steel by...
£ 14.00 -
VIRE NEW carburettor for Vire 7 or Vire 6 (tillotson HL vire)
NEW Tillotson HL carb for vire 7 or 6 (model HL 286A or HL 260A equiv...
£ 160.00
Categories
New products
-
prop Shaft Bearing ( ID 1"/25.4mm )
NOS - special high temp/low friction/low expansion bush bearing this is...
£ 48.00
Suppliers
- Fashion Supplier
Top sellers
-
-
EXCHANGE Refurbished Carburettor...
REFURBISHED Tillotson HL carb for vire 7 or 6 (model HL 286A or HL 260A equiv and others) EXCHANGE - you agree to return your old carburettor within 28 days (return addressed bag included you pay postage £30 refund conditional - read below Choke Lever option: The original carburettor had a small adjustable lever this was ideal for remote cable operation
£ 80.00Product available with different options -
PUMP SERVICE KIT
Pump service kit for Vire 7 & 12 hp engines, you get; impellor uprated drive key s/s 2 x gaskets hylomar gasket glue modified allen key and 3x s/s allen bolts to replace old bolts. instructions/tip sheet for perfect/ easy installation.
£ 45.00In Stock -
Cylinder drain plug and washer vire 7&12
plug and washer for cylinder water drain on a vire 7 or 12 Please check your thread in cylinder is ok before ordering
£ 15.00In Stock -
VIRE 12 Core Plug set (5) Stainless Steel
Specially made for Vire motors only. Pressed from stainless steel by precision engineers Exceeds Original specification Full set https://www.youtube.com/watch?v=gbUWPmfioqc
£ 24.00In Stock -
HT Cap - Waterproof ( spark plug cover )
HT Cap upgrade for the Vire 7, 12 or Vire 6 BVR engines. Correct Vire inbuilt resistance suppression, to gaurantee reliability and stop interference with your VHF etc. Waterproof HT boots on each end to prevent ignition corrosion and leakage
£ 8.00In Stock -
VIRE 7 & Vire 12 Gearbox Gasket
Vire 7 & 12 Gearbox Gasket This does not include gearbox or anything else. cut by laser at VIRE UK
£ 6.00In Stock -
PUMP SEALS overhaul KIT
kit for replacing and upgrading your pump shaft seals; 3 x double lipped seals (3 are better than 2 and will fit) 2 x s/s retaining clip (old steel ones rust and not normally re-usable) 1 x gearbox gasket (original thickness to retain thrust bearing clearances) 40g soecial reccomended HYLOMAR sealant printed tips/instructions for removing /replacing gearbox
£ 36.00In Stock -
TOP HOSE (improved Vire 7 Exhaust Jacket...
TOP HOSE for Vire 7 uprated, thicker longer and stronger than original to make watertight fit and keep suppleness longer exhaust jacket to cylinder hose. this part 52035 slides over the copper pipe 52034, and is then squashed as you bolt the silencer 67752 on. Arrow in the picture points to the part
£ 6.00In Stock -
VIRE 6/7/12 Piston Rings - Set Of 3 OEM...
NEW stock 2023 - precision machined, tested over 10 years original size for "69.79" marked STD piston ("70.35" marked pistons were very rare like 5% and no longer available) all rings chrome silver finish , should be used on all 3 gaps (less chance seizing)
£ 58.00In Stock -
CYLINDER BASE GASKET 7 hp
waterproof paper gasket, special thickness, between cylinder and crankcase check crankcase joint is level, use sealant like hylomar I have a video on youtube about this procedure
£ 6.00In Stock -
Part 1of 2 - Vire 6 BVR Manual...
Part 1 Installation guide Operators Manual (Parts List is in part 2) Published by Valmet about 1960 covers BVR model, but the engine is same as BV and BVK including common tillotson carburettor and BOSCH ignition, ( not rare WICO ignition / AMAL carburettor variants )
£ 0.00In Stock
