No products
Top sellers
-
PUMP IMPELLER /" IMPELLOR / IMPELER /ROTOR / RUBBER BLADES"
Highest Quality -Impellor / Impeller for the water pump on a Vire 7 or...
£ 24.00 -
-
Vire 7 & Vire 12 Manual 1992 + Parts List
Operators Manual Installation manual Published by a boatyard (now...
£ 0.00 -
ignition points , contact set
contact set ignition points youtube videos how to fit and set and...
£ 23.00 -
-
VIRE 7 Core Plug set (3) Stainless Steel (Freeze plug)
Specially made for Vire motors only. Pressed from stainless steel by...
£ 14.00 -
-
VIRE 7 & 12 DRIVE-KEY (woodruff key) for impeller- s/s
Highest Quality -drive key, or woodruff key this is pressed into the...
£ 4.00 -
-
VIRE 7 DYNASTART BELT (FAN BELT )
Correct Vire sized length, tooth size and V-angle, Vire 7 standard...
£ 10.00
Categories
Suppliers
- Fashion Supplier
Top sellers
-
4 x PUMP GASKET (pack of 4)
4 x PUMP GASKETS 2022 - improved LASER-cut design, easier to align and use, stronger, more accurate. essential spares, just in case! for 7 & 12 hp models (rubber impellor, high efficiency, self-priming) precise thickness required to seal impellor correctly, maximum pump performance, minimum pump wear. top quality specialist gasketmaterial, oil/salt...
£ 7.50In Stock -
-
-
EXHAUST PIPE GASKET 6 & 7HP , WITH BRASS NUTS
STEEL EXHAUST PIPE GASKET CUSTOM TO FIT VIRE ENGINE STUD-PITCH CORRECTLY INCLUDES 2 X BRASS NUT (CANNOT SEIZE AND OR LOOSEN STUDS UNLIKE STEEL NUTS)
£ 7.00In Stock -
VIRE 6/7/12 Gearbox RUBBER COUPLING SET -...
Vire 7/12 Prop-shaft RUBBER COUPLING KIT (Early Version) Does not include flanges, just the singular rubber and its bushes, to fit 6 x M8 flange pair Note: This is the Early version with 6 holes the same diameter. (Late gearbox flange has 3 x M10 threads/bushes, so this part will not fit M10 stud properly)
£ 47.00Out of stock -
VIRE 12 DYNASTART BELT (FAN BELT )
Correct Vire sized length, tooth size and V-angle, Vire 12 has higher RPM than 6/7; hence bigger dynastart pulley; hence bigger belt Tested durability Always nice to have a spare onboard Easy to fit, other belts slightly the wrong size create some difficulty fitting or premature failure The adjuster has only enough space to fit the correct belt easily...
£ 10.00In Stock -
VIRE 6/7/12 HT lead - Stranded Core (red)
HT lead for the Vire 7, 12 or Vire 6 BVR engines. RED Correct Vire resistance , to gaurantee reliability and spark strength. correct length for the Vire engines. Stranded metal core to prevent corrosion and leakage. Assists reliable quick starting in damp conditions and correct running.
£ 13.00In Stock -
Bolt Kit (allen s/s) For VIRE 7 & 12- Pump...
4mm Allen key 3 x Stainless Steel Allen (Hex) Bolts
£ 5.00In Stock -
CIRCLIP s/s (for PUMP SHAFT SEAL)
CIRCLIP, stainless steel, (for retaining a PUMP SHAFT SEAL)
£ 2.00In Stock -
Exhaust - Cylinder GASKET 12 hp
BLUE (2019 uprated version is better fit than original) gasket + also included, the 0-ring (366989) /spacer rubber in the cylinder-top water hole fits: vire 12 original alloy silencer vire 12 stainless steel 'rustfree' silencer (upgrade) re-usable?, if you use hylomar (non-setting sealant) except 'exhaust cement' just around the exhaust hole, then it...
£ 19.00In Stock -
SERVICE KIT for Carburettor on VIRE 6/7...
Vire 6 & 7 Diapragm Carb (Typically 286/260 models) The picture carburettor is not included 1 x Rubber fuel-level-diaphragm/membrane replace every 4-10 years (because petrol slowly stiffens it, and it has to stay flexible to keep air/fuel mixture perfect)
£ 32.00In Stock -
VIRE 6/7 Engine Mounting Vibration Damper...
Vire 6/ 7 Engine mounting (Steel Oval Base) includes ; Steel/rubber threaded base (70mm PCD) steel BZP stud (50 x M10) 2 x washers 1 x heaight adjusting nut 1 x lock nut
£ 25.00In Stock
