No products
Top sellers
-
PUMP IMPELLER /" IMPELLOR / IMPELER /ROTOR / RUBBER BLADES"
Highest Quality -Impellor / Impeller for the water pump on a Vire 7 or...
£ 24.00 -
-
Vire 7 & Vire 12 Manual 1992 + Parts List
Operators Manual Installation manual Published by a boatyard (now...
£ 0.00 -
ignition points , contact set
contact set ignition points youtube videos how to fit and set and...
£ 23.00 -
-
VIRE 7 Core Plug set (3) Stainless Steel (Freeze plug)
Specially made for Vire motors only. Pressed from stainless steel by...
£ 14.00 -
-
VIRE 7 & 12 DRIVE-KEY (woodruff key) for impeller- s/s
Highest Quality -drive key, or woodruff key this is pressed into the...
£ 4.00 -
-
VIRE 7 DYNASTART BELT (FAN BELT )
Correct Vire sized length, tooth size and V-angle, Vire 7 standard...
£ 10.00
Categories
Suppliers
- Fashion Supplier
Top sellers
-
Fuel Filter - Glass 10 micron desalinating
10 micron filter removes smallest contaminants desalinatingwater bowl you can easily drain supplied with tails and washers, easy to fit. essential equipment for tilloson carburettor in saltwater environment (Vire 7) input tail is bore 8mm, output tail is bore 6mm (same as modern vire carburettor inlet pipes)
£ 55.00Out of stock -
Drive Key (woodruff key for forward gear...
Highest Quality -drive key, or woodruff key this is pressed into the pump shaft to drive the forward gear pinion
£ 5.00In Stock -
Gear Bearings (Pair)
Pair Of Gearbox GEAR/CLutch Bearings For Vire 6/7/12 The pictured gear is for context and is not included
£ 24.00In Stock -
manual choke conversion kit for Vire 12...
2020 improved model choke cable (150cm) , adjuster, adaptor and new TIP this replaces the electric starting choke on a vire 12 engine comes with all you need and instructions to replace electric choke requires the spring and collar from your existing electric choke(you will see only when removed) please see my video on whats involved to fit , so google :...
£ 75.00In Stock -
Exhaust - Cylinder GASKET 7 hp
RE_usable part if you lost or damaged it and cannot make one, email me, i do have some new ones i hold in reserve for emergencies. i dont offer for sale online because i would sell loads that simply are not needed. i now have to make these using high-temperature thick gasket sheet, by hand and it takes time, so understand it may cause a day delay on any...
£ 20.00In Stock -
VIRE 6 DRIVE-KEY (woodruff key) for...
Highest Quality -drive key, or woodruff key p/n/ 8999 01432 3mm width (not 2mm width 7/12hp engines have), special height and length to fit as original this is pressed into the pump shaft to drive the Impellor / Impeller for the water pump on a Vire 6 (note this is fatter than Vire 7 or Vire 12 and ~will NOT fit those )
£ 5.00In Stock -
-
VIRE 6/7/12 OEM New DYNASTART unit...
Vire 6/7/12 OEM- BOSCH-group DYNASTART with nut, key, wiring diagram. 12 months warranty. Loyalty discount on related equipment and free Technical support for life. +£50 refund for your old exchange unit posted back to me, in 14 days, if possible please.
£ 395.00In Stock -
VIRE 6/7/12 Gearbox RUBBER COUPLING -...
Vire 7/12 Prop-shaft RUBBER COUPLING KIT (Late Version) this is no longer in production, but see assciated part, there is now a conversion kit using the much stronger new 100hp rubber. search for "coupling kit" Side Notes Late version has the 3 studs facing aft from gearbox flange, bigger (M10) and longer, so the 6 holes in this coupling disc are 2...
£ 47.00Out of stock -
FLOAT with pin for Vire 12 (Bing carburettor)
FLOAT and float pin NEW for the BING carb on a vire 12 (model 8/25/179 equiv and others)
£ 29.00In Stock -
PUMP SHAFT EXCHANGE (£100 refund) Vire 7
RE-furbished, the shaft seal area is uprated to Stainless-steel, correcting an original saltwater design fault. Exchange; I need to charge you +£100 deposit, refundable on return of your old assembly within 28 days. Then i will refund your £100
£ 249.00In Stock -
Rod Bearing (Big End Bearing)
Rod bearing (Big end bearing) 52293/6 special high pressure, caged roller bearing, fits between crank pin and the steel con rod fitted on engines (Vire 7 & 12) numbers >22000 note :earlier engines numbered <22000 had a different bearing (52293) to fit the alloy con rods
£ 38.00In Stock
