No products
Top sellers
-
PUMP IMPELLER /" IMPELLOR / IMPELER /ROTOR / RUBBER BLADES"
Highest Quality -Impellor / Impeller for the water pump on a Vire 7 or...
£ 24.00 -
-
Vire 7 & Vire 12 Manual 1992 + Parts List
Operators Manual Installation manual Published by a boatyard (now...
£ 0.00 -
ignition points , contact set
contact set ignition points youtube videos how to fit and set and...
£ 23.00 -
-
VIRE 7 Core Plug set (3) Stainless Steel (Freeze plug)
Specially made for Vire motors only. Pressed from stainless steel by...
£ 14.00 -
-
VIRE 7 & 12 DRIVE-KEY (woodruff key) for impeller- s/s
Highest Quality -drive key, or woodruff key this is pressed into the...
£ 4.00 -
-
VIRE 7 DYNASTART BELT (FAN BELT )
Correct Vire sized length, tooth size and V-angle, Vire 7 standard...
£ 10.00
Categories
Suppliers
- Fashion Supplier
Top sellers
-
piston pin (gudgeon or wrist pin)
Piston pin Fits ALL vire engines (6/7/12), ALL years precision machined part, very rare, correct specification, tested 2mm shorter in length than original, so easier to fit
£ 25.00In Stock -
O-ring for Exhaust - Cylinder 12 hp
0-ring/spacer rubber in the cylinder-top water hole special high temperature, extra thick, correct diameter, ensuring raised compressible fit to gasket. fitted to cylinder head recess in top starboard side fits: vire 12 original alloy silencer vire 12 stainless steel 'rustfree' silencer (upgrade)
£ 4.00In Stock -
TOP PIPE (Vire 7 Exhaust Jacket To...
TOP PIPE for Vire 7 REFURBISHED metal (low corrosion), straight/bent
£ 14.00Out of stock -
VIRE 6/7/12 Main Bearing Set (Pair) - Steel
Main bearing (crankshaft) pair for the Vire 7 or Vire 12 or Vire 6 BVR engines. This is for 2 (pair) since you always change a pair. Quality - Steel Up-rated Stainless Bearings Also Available (Guaranteed Long-Life): Please See Other Items
£ 58.00In Stock -
CRANK SHAFT SEAL
1 x crankcase SEAL for the Vire engines (If you want a set, please purchase 2x for 6hp, 3x for Vire 7/12) High Quality, double-lipped, type-tested over 15 years by VIRE UK, no failures.
£ 18.00In Stock -
CYLINDER BASE GASKET 12 hp
special extra thickness, critical to correct compression ratio, avoiding piston damage, designed only for the 12hp model waterproof paper gasket, special thickness, between cylinder and crankcase check crankcase joint is level, use sealant like hylomar I have a video on youtube about this procedure
£ 15.00In Stock -
manual choke conversion kit for Vire 12...
choke cable (30cm) and adaptor this replaces the electric starting choke on a vire 12 engine
£ 45.00Out of stock -
Vire 2018 stainless steel Exhaust ( fits 7...
NEW in 2018 ! youtube video custom upgrade in stainless steel, rustfree, special design fits both 7hp and 12hp models built-in watertrap and water injection (like old alloy vire 12) lugs for attaching morse cables and choke cables directly, accurate copy with better quality and features best exhaust system available for Vire 7 /12, cures all known issues,...
£ 595.00In Stock -
connector block / connecting rail 4-pole
NEW for 2021 fits above the flywheel holds the 4 wires from the ignition
£ 12.00In Stock -
Intake Manifold Assembly (for Tillotson...
refurbished Intake Manifold Assembly: part 59654 aluminium flame arrester/air filter top, usually, slight dents or scratches in alloy not affecting operation 2 steel fixing bolts and brass spacers aluminium Elbow new laser-cut gasket( essential with elbow to prevent drips)
£ 69.00In Stock -
VIRE 6/7/12 Thrust Bearing
Thrust bearing for Gearbox (will fit either end of gear-shaft) for the Vire 6/7/12 1 precision bearing is included The pictured gear-shaft is for context and is not included.
£ 29.00Out of stock -
VIRE NEW carburettor for Vire 12 (BING vire)
NEW BING carb for vire 12 (model 8/25/179 equiv and others) NOT included ;electric choke, air filter,throttle lever (re-use yours)
£ 245.00Out of stock
