No products
Top sellers
-
PUMP IMPELLER /" IMPELLOR / IMPELER /ROTOR / RUBBER BLADES"
Highest Quality -Impellor / Impeller for the water pump on a Vire 7 or...
£ 24.00 -
-
Vire 7 & Vire 12 Manual 1992 + Parts List
Operators Manual Installation manual Published by a boatyard (now...
£ 0.00 -
ignition points , contact set
contact set ignition points youtube videos how to fit and set and...
£ 23.00 -
-
VIRE 7 Core Plug set (3) Stainless Steel (Freeze plug)
Specially made for Vire motors only. Pressed from stainless steel by...
£ 14.00 -
-
VIRE 7 & 12 DRIVE-KEY (woodruff key) for impeller- s/s
Highest Quality -drive key, or woodruff key this is pressed into the...
£ 4.00 -
-
VIRE 7 DYNASTART BELT (FAN BELT )
Correct Vire sized length, tooth size and V-angle, Vire 7 standard...
£ 10.00
Categories
Suppliers
- Fashion Supplier
Top sellers
-
Fuel Filter - METAL inline 10 micron
10 micron, disposable, FIRE-RETARDANT METAL Disposable filter for (8mm) Pipe hose (inside diameter) You must have a fuel filter for all vire engines, this one will NOT remove saltwater/water, but it will remove fine salts and grit if you cannot afford a desalinating filter, then please have one of these at least!
£ 15.00In stock -
-
VIRE 6/7/12 ONE Piston Ring - (1x )OEM...
1 x ring ONLY (i also sell set of 3) NEW stock 2023 - precision machined, tested over 10 years original size for "69.79" marked STD piston ("70.35" marked pistons were very rare like 5% and no longer available) ring is chrome silver finish , can be used on any of your 3 gaps (less chance seizing)
£ 24.00In Stock -
PUMP PLATE
PUMP PLATE NEW RARE ORIGINAL (zero wear) this is the BRONZE plate that fits between the gearbox casting gasket, and the pump housing gasket (vire #52120 in the 1992 parts manual ;page p25 #5) for 7 & 12 hp models (rubber impellor, high efficiency, self-priming)
£ 95.00Out of stock -
Carburettor-Elbow GASKET 7 hp
Gasket Stops fuel dripping at low RPM from the joint between the carburettor and the elbow under the air filter these are now laser cut, so you may receive 1 thick one or 2 thin ones that you should use together. I advise do not use gasket glue on the carburettor side, so you can dismantle your elbow in future without tearing your gaskets.
£ 3.50In Stock -
VIRE 7 ENGINE COMPLETE. REFURBISHED...
-£100 non exchange surcharge included, you will get refunded on return of your V7. Refurbished and upgraded Vire 7 complete. Early model, high hours, rebuilt to order 3 week delivery. new internal steel main bearings, uprated s/s pump shaft standard quick paint finish to save cost
£ 1,595.00In Stock -
VIRE 6 BVR EXHAUST (6 BHP)
£30 Refund On Your Old Unit Returned. Fully Refurbished: Working condition aluminium exhaust. Cast steel elbow bolted on Water injection pipe brazed in watertight (smoke and carbon monoxide prevention) New cylinder gasket New pair brass cylinder exhaust nuts Outlet pipe ready for attatching 40mm standard rubber hose
£ 120.00In Stock -
Main Crankshaft Bearings Set (Pair) -...
Upgraded (stainless steel - corrosion resistant) Main bearing (crankshaft) pair for the Vire 7 or Vire 12 or Vire 6 BVR engines. This is for 2 (pair) since you always change a pair. Quality Stainless - Steel Restores quiet running. The original bearings are usually inferior quality Russian/E. Block. and lasted about 10 seasons manufactured in Finland.
£ 124.00In Stock -
VIRE 6/7 Idler Gear Bearings (Pair)
Pair Of Gearbox Idler Bearings (Reversing Gear) For Vire 6/7/12 The pictured idler gear is for context and is not included
£ 34.00In Stock -
VIRE 6 Crank SEAL (Pair)
Pair crankcase SEALS for the Vire 6 BVR engines (Vire 7/Vire 12 requires 3 seals per engine). This is for 2 (pair) as you will always change a pair on a Vire 6. High Quality
£ 26.00In Stock -
VIRE 7/12 Engine Adaptor Plates (wider...
instead of lowering/weakening your engine bearers or rubber mountings or hull, these can be used to relocate the original engine mounting holes higher, wider and a little longer ! 2 x special plates, manufactured by Vire (56622 & 56621 in the original Valmet A4 size parts list )
£ 45.00In Stock -
Teleflex Single Lever Side Mount (Vire...
Teleflex Dual action (gear & throttle) inboard engine control lever, recommended model for the VIRE inboard engines. (See full description for specific requirements). vire part number 58170 Features • Dual action (throttle and shift in one lever)• Flush mount design • Neutral “warm up” button for throttle only operation • will fit standard teleflex...
£ 259.00In Stock
