No products
Vire 6hp engine, had a round cylinder shape, or model 'BV' most commonly with a Reversing gearbox from Circa 1959 model 'BVR'. produced until 1973
Vire 6hp There are 68 products.
-
Fuel Filter - with Priming button
with integral priming button, quick restart after running out of fuel 10 micron filter removes smallest contaminants desalinating and also water removing bowl you can drain, metal fire-resistantant supplied with tails and washers input tail is bore 8mm, output tail is bore 8mm , for cutting and inserting into rubber fuel line, although they are on the...
£ 65.00Out of stock -
Cylinder drain plug and washer vire 7&12
plug and washer for cylinder water drain on a vire 7 or 12 Please check your thread in cylinder is ok before ordering
£ 15.00Out of stock -
VIRE NEW carburettor for Vire 7 or Vire 6...
NEW Tillotson HL carb for vire 7 or 6 (model HL 286A or HL 260A equiv and others) out of stock june 24 but new stock arriving early july 24 preorders accepted.
£ 185.00In Stock -
WICO ignition points (contact set)
points that fit the WICO ignition system used on early Vire6 engines only i have a few old sets if you are desperate, please contact me if you need these or photos of the general type
£ 23.00Out of stock -
Main Crankshaft Bearings Set (Pair) -...
Upgraded (stainless steel - corrosion resistant) Main bearing (crankshaft) pair for the Vire 7 or Vire 12 or Vire 6 BVR engines. This is for 2 (pair) since you always change a pair. Quality Stainless - Steel Restores quiet running. The original bearings are usually inferior quality Russian/E. Block. and lasted about 10 seasons manufactured in Finland.
£ 124.00In Stock -
VIRE 6/7/12 Main Bearing Set (Pair) - Steel
Main bearing (crankshaft) pair for the Vire 7 or Vire 12 or Vire 6 BVR engines. This is for 2 (pair) since you always change a pair. Quality - Steel Up-rated Stainless Bearings Also Available (Guaranteed Long-Life): Please See Other Items
£ 58.00In Stock -
VIRE 6/7/12 Pump Bearing Double Race...
New pump bearing bearings for Gearbox for the Vire 6/7/12 . This bearing is highest quality Vire Marine Spec. The pictured pump shaft shown is for context and is not included
£ 35.00In Stock -
VIRE 6/7 Idler Gear Bearings (Pair)
Pair Of Gearbox Idler Bearings (Reversing Gear) For Vire 6/7/12 The pictured idler gear is for context and is not included
£ 34.00In Stock -
VIRE 6/7/12 Thrust Bearing
Thrust bearing for Gearbox (will fit either end of gear-shaft) for the Vire 6/7/12 1 precision bearing is included The pictured gear-shaft is for context and is not included.
£ 29.00In Stock -
VIRE 6 Crank SEAL (Pair)
Pair crankcase SEALS for the Vire 6 BVR engines (Vire 7/Vire 12 requires 3 seals per engine). This is for 2 (pair) as you will always change a pair on a Vire 6. High Quality
£ 26.00In Stock -
VIRE 6 DYNASTART BELT (FAN BELT )
Vire sized length, tooth size and V-angle Vire 6 has lower RPM than 7/12; hence bigger flywheel pulley, longer V6 adjuster; hence bigger belt Tested durability Always nice to have a spare onboard Easy to fit, others slightly the wrong size create difficulty fitting or premature failure Please check pulleys inline and smooth or you may get premature wear....
£ 10.00In Stock -
