No products
Vire 12hp model produced Circa 1975-2002.
Identifiable by the spark plug being on the front of the cylinder. Bing float carburettor with seperate bing pump under it. Electric solenoid starting choke originally used.
Vire 12 HP There are 88 products.
-
Fuel Filter - with Priming button
with integral priming button, quick restart after running out of fuel 10 micron filter removes smallest contaminants desalinating and also water removing bowl you can drain, metal fire-resistantant supplied with tails and washers input tail is bore 8mm, output tail is bore 8mm , for cutting and inserting into rubber fuel line, although they are on the...
£ 65.00Out of stock -
Cylinder drain plug and washer vire 7&12
plug and washer for cylinder water drain on a vire 7 or 12 Please check your thread in cylinder is ok before ordering
£ 15.00Out of stock -
Main Crankshaft Bearings Set (Pair) -...
Upgraded (stainless steel - corrosion resistant) Main bearing (crankshaft) pair for the Vire 7 or Vire 12 or Vire 6 BVR engines. This is for 2 (pair) since you always change a pair. Quality Stainless - Steel Restores quiet running. The original bearings are usually inferior quality Russian/E. Block. and lasted about 10 seasons manufactured in Finland.
£ 124.00In Stock -
VIRE 6/7/12 Main Bearing Set (Pair) - Steel
Main bearing (crankshaft) pair for the Vire 7 or Vire 12 or Vire 6 BVR engines. This is for 2 (pair) since you always change a pair. Quality - Steel Up-rated Stainless Bearings Also Available (Guaranteed Long-Life): Please See Other Items
£ 58.00In Stock -
VIRE 6/7/12 Gearbox RUBBER COUPLING -...
Vire 7/12 Prop-shaft RUBBER COUPLING KIT (Late Version) this is no longer in production, but see assciated part, there is now a conversion kit using the much stronger new 100hp rubber. search for "coupling kit" Side Notes Late version has the 3 studs facing aft from gearbox flange, bigger (M10) and longer, so the 6 holes in this coupling disc are 2...
£ 47.00Out of stock -
VIRE 6/7/12 Gearbox RUBBER COUPLING SET -...
Vire 7/12 Prop-shaft RUBBER COUPLING KIT (Early Version) Does not include flanges, just the singular rubber and its bushes, to fit 6 x M8 flange pair Note: This is the Early version with 6 holes the same diameter. (Late gearbox flange has 3 x M10 threads/bushes, so this part will not fit M10 stud properly)
£ 47.00In Stock -
VIRE 6/7/12 Pump Bearing Double Race...
New pump bearing bearings for Gearbox for the Vire 6/7/12 . This bearing is highest quality Vire Marine Spec. The pictured pump shaft shown is for context and is not included
£ 35.00In Stock -
VIRE 6/7 Idler Gear Bearings (Pair)
Pair Of Gearbox Idler Bearings (Reversing Gear) For Vire 6/7/12 The pictured idler gear is for context and is not included
£ 34.00In Stock -
VIRE 6/7/12 Thrust Bearing
Thrust bearing for Gearbox (will fit either end of gear-shaft) for the Vire 6/7/12 1 precision bearing is included The pictured gear-shaft is for context and is not included.
£ 29.00In Stock -
VIRE 12 DYNASTART BELT (FAN BELT )
Correct Vire sized length, tooth size and V-angle, Vire 12 has higher RPM than 6/7; hence bigger dynastart pulley; hence bigger belt Tested durability Always nice to have a spare onboard Easy to fit, other belts slightly the wrong size create some difficulty fitting or premature failure The adjuster has only enough space to fit the correct belt easily...
£ 10.00In Stock -
-
PUMP IMPELLER /" IMPELLOR / IMPELER /ROTOR...
Highest Quality -Impellor / Impeller for the water pump on a Vire 7 or Vire 12
£ 24.00In Stock
