No products
New products
-
prop Shaft Bearing ( ID 1"/25.4mm )
NOS - special high temp/low friction/low expansion bush bearing this is...
£ 48.00
Vire 6hp engine, had a round cylinder shape, or model 'BV' most commonly with a Reversing gearbox from Circa 1959 model 'BVR'. produced until 1973
Vire 6hp There are 67 products.
-
CRANK SHAFT SEAL
1 x crankcase SEAL for the Vire engines (If you want a set, please purchase 2x for 6hp, 3x for Vire 7/12) High Quality, double-lipped, type-tested over 15 years by VIRE UK, no failures.
£ 18.00In Stock -
CYLINDER BASE GASKET 6 hp
waterproof paper gasket, special thickness, between cylinder and crankcase check crankcase joint is level, use sealant like hylomar I have a video on youtube about this procedure
£ 6.00In Stock -
ignition condenser / capacitor
Bosch OEM Vire 6/7/12 ignition condenser https://www.youtube.com/watch?v=AI25X6uqdrE
£ 12.00In Stock -
Fuel Filter - Glass 10 micron desalinating
10 micron filter removes smallest contaminants desalinatingwater bowl you can easily drain supplied with tails and washers, easy to fit. essential equipment for tilloson carburettor in saltwater environment (Vire 7) input tail is bore 8mm, output tail is bore 6mm (same as modern vire carburettor inlet pipes)
£ 55.00Out of stock -
Fuel Filter - Cheap minimal
50 micron, disposable, Transparent Disposable filter for 1/4" (6mm) or 5/16" (8mm) Pipe hose (inside diameter) push fit and clip to rubber fuel hose only. You must have a fuel filter for all vire engines, this one will NOT remove saltwater/water/fine salts and particles, but it is better than nothing. if you cannot afford a desalinating filter, then...
£ 3.95In stock -
VIRE 6/7 Engine Mounting Vibration Damper...
Vire 6/ 7 Engine mounting (Steel Oval Base) includes ; Steel/rubber threaded base (70mm PCD) steel BZP stud (50 x M10) 2 x washers 1 x heaight adjusting nut 1 x lock nut
£ 25.00In Stock -
ignition points , contact set
contact set ignition points youtube videos how to fit and set and diagnose https://www.youtube.com/watch?v=sT_IDcJYa84 removing https://www.youtube.com/watch?v=lclSeSUlYlQ installing
£ 23.00In Stock -
piston pin (gudgeon or wrist pin)
Piston pin Fits ALL vire engines (6/7/12), ALL years precision machined part, very rare, correct specification, tested 2mm shorter in length than original, so easier to fit
£ 25.00In Stock -
Crank Pin (Big End Pin)
correct part number is 52008 (52208 printed in Denmark manual isincorrect but is fig.17 page 24) Crank pin, Big end pin
£ 42.00In Stock -
ignition coil
ignition coil youtube videos how to fit and set and diagnose bosch replacement https://www.youtube.com/watch?v=l7L5EolHfts static test using battery https://www.youtube.com/watch?v=YJKKf1FLGcY running test using strobe lamp
£ 110.00In Stock -
Drive Key (woodruff key for forward gear...
Highest Quality -drive key, or woodruff key this is pressed into the pump shaft to drive the forward gear pinion
£ 5.00In Stock -
VIRE 6/7 Engine Mounting Vibration Dampers...
pack of 4 x Vire 6/ 7 Engine mounting (Steel Oval Base) each includes ; Steel/rubber threaded base (70mm PCD) steel BZP stud (50 x M10) 2 x washers 1 x heaight adjusting nut 1 x lock nut
£ 90.00In Stock
