Highest Quality -Impellor / Impeller for the water pump on a Vire 7 or...
Operators Manual Installation manual Published by a boatyard (now...
contact set ignition points youtube videos how to fit and set and...
Highest Quality -drive key, or woodruff key this is pressed into the...
Vire 6 & 7 Diapragm Throttle Shaft (Typically 286/260 models)...
Correct Vire sized length, tooth size and V-angle, Vire 7 standard...
Specially made for Vire motors only. Pressed from stainless steel by...
Suppliers
BLUE (2019 uprated version is better fit than original) gasket + also included, the 0-ring (366989) /spacer rubber in the cylinder-top water hole fits: vire 12 original alloy silencer vire 12 stainless steel 'rustfree' silencer (upgrade) re-usable?, if you use hylomar (non-setting sealant) except 'exhaust cement' just around the exhaust hole, then it...
STEEL EXHAUST PIPE GASKET CUSTOM TO FIT VIRE ENGINE STUD-PITCH CORRECTLY INCLUDES 2 X BRASS NUT (CANNOT SEIZE AND OR LOOSEN STUDS UNLIKE STEEL NUTS)
with integral priming button, quick restart after running out of fuel 10 micron filter removes smallest contaminants desalinating and also water removing bowl you can drain, metal fire-resistantant supplied with tails and washers input tail is bore 8mm, output tail is bore 8mm , for cutting and inserting into rubber fuel line, although they are on the...
Part 2 of the Vire 6 manual Fault-finding Parts List Published by Valmet about 1960 covers BVR model, but the engine is same as BV and BVK including common tillotson carburettor and BOSCH ignition, ( not rare WICO ignition / AMAL carburettor variants )
Vire 6 & 7 Diapragm Carb (Typically 286/260 models) The picture carburettor is not included 1 x Rubber fuel-level-diaphragm/membrane replace every 4-10 years (because petrol slowly stiffens it, and it has to stay flexible to keep air/fuel mixture perfect)
Puller kit to remove the flywheel, all vire models NEW 2021, custom designed and tested by myself on all vire engine models this is improved as it is stronger steel, finer pitch central bolt in a hub that stays flat and true unlike previous versions - see full description about the 2021 enhancements
Operators Manual NO Parts List (download the later 7/12 manual) Published by Valmet 1987 Oil:Petrol mix The amount of oil mixed in petrol depends on engine numbers ( con-rod / piston pin bearing type) ; 10000- 22000 need 3% oil because they have bronze bush (in silver aluminium con-rod) 22001 -02000 need 2% oil because they are fitted with needle...
ignition coil youtube videos how to fit and set and diagnose bosch replacement https://www.youtube.com/watch?v=l7L5EolHfts static test using battery https://www.youtube.com/watch?v=YJKKf1FLGcY running test using strobe lamp
Highest Quality -drive key, or woodruff key this is pressed into the crank shaft to locate the flywheel
starting solenoid Bosch marinised plastic case and protected non-rusting contacts uprated to 250A instantaneous/125A continuous (double the original Vire standard) ( for all types of dynastarts )
Vire 7/12 Prop-shaft RUBBER COUPLING CONVERSION KIT (Late Version) enables you to fit the stronger uprated coupling rubber, to a vire 12 or later vire 7 replacethe 3 m10 studs with bolts or stretch over them and fit bushes. ~(youtube videos) 1 of uprated rubber coupling 2 of m10 nuts(tool) 3 of m8 bolts with washers and nuts 3 of m10 bushes, washers...
Set of 3x crankcase SEALS for the Vire 7/12 engine High Quality, type tested by VIRE UK over 15 years, no failures